Home > Intruder Alarm > Scantronic > Scantronic I-on
Catalogue No: I-ON40HBrand: Scantronic
Click for delivery info
i-on40 is a 40 zone control unit for hybrid wired/wirefree alarm systems intended for domestic and light commercial use.
The control unit comprises an end station with remote keypads. The simple-to-install end station has an ABS plastic case which contains the radio transceiver, power supply and backup battery. Up to four keypads connect to the end station by standard alarm cable, allowing the end user to set and unset the system, and the installer to fully configure the control unit. The keypads also contain integral proximity tag readers, so that end users can control the system without having to remember access codes.
The control unit works with Cooper Security Ltd's 700 series 868MHz narrowband wireless peripherals.
During programming the installer can set up the system as either a part setting system with full set and three part sets, or a partitioned system where each of the four partitions has full set and a single part set.
The i-on40 offers a wide range of communication options. Plug-on modules provide connection to either the telephone system (PSTN), the mobile phone network (GSM) or the internet via Ethernet or GPRS. In addition, the control unit provides a set of output pins which can be used to drive stand-alone communicators.
To make the installation and maintenance simple, the control unit also provides Ethernet and USB connectors for attaching PCs or laptops. The control unit can be programmed using a standard web browser from an Ethernet connected laptop, or by Cooper Security's Downloader software using the on-board USB port. In addition, if the control unit is fitted with a PSTN module the installer can use Downloader for remote maintenance.
40 zone hybrid endstation with remote keypads.
Cooper Security Ltd.
Tested -10 to +55°C.
0 to 75% RH, non-condensing.
384 x 245 x 94, mm HxWxD.
115 x 156 x 34, mm HxWxD
2.2 kg (without stand-by battery).
24 radio, 16 wired.
16 wired (comprising two voltage free contacts, 14 transistorised of which 12 are provided on two separate wiring harnesses).
8 radio (with suitable products such as the 770r Wireless Accessory Module).
±10 minutes over one year (depending on the accuracy of the mains supply frequency).
External Radio Sirens
Internal Radio Sounders
Up to 1,000 events, stored in flash memory (requires no support battery)
Radio detector differs
16,777,214 (2 24 -2).
4 digits, all four digits may be any number 0 to 9, giving 10,000 differs.
Number of access codes
50 plus installer
Blocked for 90s after four incorrect codes in series.
Proximity tag differs
Operating frequency 868.6625MHz Narrowband.
EN 300 220-3.
EN 300 330-2
The range of the transmitters compatible with this control unit depends on the environment in which they are installed. As a guideline, most transmitters will work up 200m range in free space conditions.
This product complies with the requirements of EN50131-6 Type A power supply at security grade 2 and environmental class II.
Mains power supply
230VAC +10%/-15%, 170mA max, 50Hz.
End station psu
13.7VDC, 1.5A max
End station consumption
30mA (backlight off)
45mA (backlight on)
65mA (backlight on max)
12V, 7Ah sealed lead acid.
More than 12 hours depending on ancillaries connected to control unit.
Max recharge time:
less than 72 hours.
Battery charge limit
12V Aux supply (inc LS)
13.7VDC +0.1/-0.4 @ 850mA max.
14.4V +0.1/-0.2 @ 230mA
12V Keypad bus
13.7V =0.1/-0.5 @ 400mA max
Mains fail, battery low voltage, battery failure.
Conforms to EN50130-4.
Conforms to EN61000-6-3.
O/P 1 - 2
Voltage free, single pole relay contacts rated 24VDC @ 1A or 120VAC @ 0.5A.
O/P 3 - 4
Open collector transistor, +12VDC when inactive, 0V when active. 500mA max.
O/P 5 - 16
Min impedance 16 Ohm, current consumption from 12VAux = 280mA in alarm.
The control unit has a T250mA mains fuse.
Conforms to EN60950-1.
This product is suitable for use in systems designed to comply with PD 6662: 2004 at grade 2 and environmental class II.
This product complies with the requirements of EN50131-3 at grade 2 and environmental class II.
This product complies with the requirements of EN50131-6:2008 at grade 2 and environmental class II.
When fitted with an i-sd02 this equipment is compliant with EN 50136-1. It allows the alarm transmission system to meet the performance requirements of EN 50131-1:2006 ATS 2 provided that:
a) It is installed in accordance with the installation instructions.
b) The connected PSTN is functioning normally.
Scantronic I-ON I-FB01 wireless key fob£48.60 £26.33
Scantronic I-ON wired keypad I-KP01£119.98 £70.13
Scantronic I-ON wired keypad K01 No Prox£84.12 £45.57
Scantronic I-ON wired keypad KPZ01 Prox plus 2 zones£166.63 £90.26
Education, Council, NHS, Police and Emergency ServicesClick Here
© 2017 OLSP Limited.
Order Helpline 0800 880 6123email: @ click here